Mazda 3 since 2003
1. Operation and car maintenance
1.1. Car description
1.2. System of passive safety
1.3. Car use to destination
1.4. Elimination of the malfunctions which have arisen in a way or before a start of motion
1.4.1. Spare wheel and set of tools
1.4.2. Engine overheat
1.4.3. Car evacuation
1.4.4. General information and security measures at control survey and car maintenance
1.4.4.1. Check of level of engine oil
1.4.4.2. Check of level of cooling liquid
1.4.4.3. Check of level of working liquid in a tank of the steering hydraulic booster
1.4.4.4. Check of level of working liquid of automatic transmission
1.4.4.5. Check and adjustment of the parking brake
1.4.4.6. Check axial люфта steering wheel
1.4.4.7. Replacement of the oil filter
1.4.4.8. Replacement of engine oil
1.4.4.9. Check of level and oil replacement in MKPP
1.4.4.10. Check of level of liquid of washers of glasses and headlights
1.4.4.11. Greasing of knots of a friction on a car body
1.4.4.12. Replacement of a filtering element of the filter of an air purifier
1.4.4.13. Replacement of brushes of a cleaner of a windscreen
1.4.4.14. Service of the storage battery
1.4.4.15. Check of level of electrolit
1.4.4.16. Charge of the storage battery
1.4.4.17. Check of pressure of air in tires
1.4.4.18. Periodic shift of wheels
1.4.5. Lamps of devices of lighting and light alarm system
1.4.6. Care of a body and car salon
1.5. Tables
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
 







f084bf0f

1-4-4-13-zamena-shhetok-ochistitelya-vetrovogo-stekla.html

1.4.4.13. Replacement of brushes of a cleaner of a windscreen

Pollution of a windscreen and edges of brushes of a screen wiper various substances reduces quality of purification of glass. Similar pollution treat, for example insects, the juice allocated by leaves of trees, and also polyroles which put in a hot condition on a car body on some automobile sinks.
If brushes badly clear glasses, wash out glass and edges of brushes an effective cleaner or soft detergent, then carefully rinse them pure water. If necessary repeat processing of glass and brushes. Bad work of a screen wiper can be caused by wear or cracks of edges of brushes. Replace worn-out edges or brushes.
1. Lift the lever of a screen wiper and turn a brush concerning the hinge so that to open access to a plastic pad of a clamp.

Fig. 1.182. Scheme of replacement of brushes of a cleaner of a windscreen


Shift a brush down (on an arrow, as is shown in drawing 1.182). Then remove a brush from the screen wiper lever.
2. Unbend down the end of a rubber edge and extend it from the holder.
3. Take out spring edges from a rubber edge and insert them into a new edge of a brush.
4. Carefully insert a new rubber edge. Then establish a brush assembled on the screen wiper lever, operating in return sequence.

ATTENTION
Do not bend and do not throw out spring edges. They are subject to a reuse. If not to establish in an edge spring edges, quality of purification of glass will worsen.
It is forbidden to use the spring edges which have been removed from the left brush of a screen wiper, for installation in the right brush, and on the contrary. Be convinced of installation of spring edges in a new edge of a brush of a screen wiper that the bend of an edge remained the same.


«previous page
1.4.4.12. Replacement of a filtering element of the filter of an air purifier
following page»
1.4.4.14. Service of the storage battery