Mazda 3 since 2003
	1. Operation and car maintenance
	2. Engine
		2.1. General description of new engines of the L8, LF and L3 models
		2.2. Mechanical part of engines
			2.2.1. Engines of the L8 and LF models
			2.2.2. Verification of the contents WITH / SN in the fulfilled gases
			2.2.3. Compression measurement in engine cylinders
			2.2.4. Check of a belt of a drive of auxiliary units
			2.2.5. General information and safety measures at removal of the power unit
			2.2.6. Hermetic removal
			2.2.7. Removal and installation of the power unit
			2.2.8. Check of the executive mechanism of change of phases of a gazoraspredeleniye (L3)
			2.2.9. Removal and installation of the executive mechanism of change of phases of a gazoraspredeleniye (L3)
			2.2.10. Chain of a drive of the mechanism of a gazoraspredeleniye
			2.2.11. Removal and installation of the operating oil valve (OCV) (L3)
			2.2.12. Check of the operating oil valve (OCV) (L3)
			2.2.13. Check of operation of the zolotnikovy valve (OCV) (L3)
			2.2.14. The general repair operations on the power unit
				2.2.14.1. Dismantling of a head of the block of cylinders (beginning)
				2.2.14.2. Dismantling of a head of the block of cylinders (termination)
				2.2.14.3. Dismantling of the block of cylinders (beginning)
				2.2.14.4. Removal and installation of a back epiploon of a cranked shaft
				2.2.14.5. Dismantling of the block of cylinders (termination)
			2.2.15. Check of a head of the block of cylinders
			2.2.16. Assembly of the block of cylinders (beginning)
			2.2.17. Assembly of the block of cylinders (termination)
			2.2.18. Assembly of a head of the block of cylinders
			2.2.19. Assembly of a drive of the mechanism of a gazoraspredeleniye
		2.3. Appendix 1
		2.4. Appendix 2
		2.5. Appendix 3
		2.6. The Z6 engine – a mechanical part
		2.7. Greasing system
		2.8. Cooling system
		2.9. Admission system
		2.10. Fuel system
		2.11. System of production of the fulfilled gases and system of decrease in toxicity
		2.12. Ignition system
		2.13. Control system
		2.14. Tables
	3. Transmission
	4. Running gear
	5. Steering mechanism
	6. Brake system
	7. Onboard electric equipment
	8. Body

2-2-14-4-snyatie-i-ustanovka-zadnego-salnika-kolenchatogo-vala.html

2.2.14.4. Removal and installation of a back epiploon of a cranked shaft

Fig. 2.130. Removal of a back epiploon of a cranked shaft: 1–bolts; 2–epiploon

Turn off six bolts of fastening of a back epiploon and remove an epiploon (fig. 2.130).

Fig. 2.131. Places of drawing of hermetic

Put kremniyevoorganichesky hermetic on being interfaced surfaces in a place shown in drawing 2.131. Diameter of a point of drawing of 0,4-0,6 mm.

Put pure engine oil on a working edge of a new epiploon.

Fig. 2.132. Scheme of installation of a back epiploon of a cranked shaft: 1–cranked shaft; 2–back epiploon; 3–the adaptation for installation; 4–block of cylinders

Establish and press a back epiploon, using the adaptation for detail installation, as is shown in drawing 2.132.

Fig. 2.133. Order of a tightening of bolts of fastening of a back epiploon of a cranked shaft

Tighten bolts of fastening of a back epiploon in an order specified in drawing 2.133, the moment of an inhaling of 8,0-11,5 N · m.

«previous page
2.2.14.3. Dismantling of the block of cylinders (beginning)

following page»
2.2.14.5. Dismantling of the block of cylinders (termination)