Mazda 3 since 2003
1. Operation and car maintenance
2. Engine
2.1. General description of new engines of the L8, LF and L3 models
2.2. Mechanical part of engines
2.2.1. Engines of the L8 and LF models
2.2.2. Verification of the contents WITH / SN in the fulfilled gases
2.2.3. Compression measurement in engine cylinders
2.2.4. Check of a belt of a drive of auxiliary units
2.2.5. General information and safety measures at removal of the power unit
2.2.6. Hermetic removal
2.2.7. Removal and installation of the power unit
2.2.8. Check of the executive mechanism of change of phases of a gazoraspredeleniye (L3)
2.2.9. Removal and installation of the executive mechanism of change of phases of a gazoraspredeleniye (L3)
2.2.10. Chain of a drive of the mechanism of a gazoraspredeleniye
2.2.11. Removal and installation of the operating oil valve (OCV) (L3)
2.2.12. Check of the operating oil valve (OCV) (L3)
2.2.13. Check of operation of the zolotnikovy valve (OCV) (L3)
2.2.14. The general repair operations on the power unit
2.2.15. Check of a head of the block of cylinders
2.2.16. Assembly of the block of cylinders (beginning)
2.2.17. Assembly of the block of cylinders (termination)
2.2.18. Assembly of a head of the block of cylinders
2.2.19. Assembly of a drive of the mechanism of a gazoraspredeleniye
2.3. Appendix 1
2.4. Appendix 2
2.5. Appendix 3
2.6. The Z6 engine – a mechanical part
2.7. Greasing system
2.8. Cooling system
2.9. Admission system
2.10. Fuel system
2.11. System of production of the fulfilled gases and system of decrease in toxicity
2.12. Ignition system
2.13. Control system
2.14. Tables
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
 







f084bf0f

2-2-13-proverka-raboty-zolotnikovogo-klapana-ocv-l3.html

2.2.13. Check of operation of the zolotnikovy valve (OCV) (L3)

Disconnect a negative wire of the storage battery.
Remove the operating oil valve.

Fig. 2.118. Primary verification of the provision of the zolotnikovy valve of the operating oil valve: 1–zolotnikovy valve


Check position of the zolotnikovy valve of the operating oil valve. It should is in the provision of the maximum delay of the moment of opening or closing of valves of the engine, as is shown in drawing 2.118.
If the result of measurement differs from the standard characteristic of indications of an ohmmeter, replace the operating oil valve.
Be convinced of that the storage battery is completely charged. If it not so, charge the storage battery.
Submit tension of the storage battery on conclusions of the operating oil valve and be convinced that the zolotnikovy valve works and moves to the provision of the maximum advancing of opening or closing of valves of the engine. If the result of measurement differs from the standard characteristic of indications of an ohmmeter, replace the operating oil valve.

NOTE
Options of giving of tension of the storage battery on conclusions of the operating oil valve:
– Accumulator plus – on A conclusion, a minus – on B conclusion
– Accumulator plus – on B conclusion, a minus – on A conclusion



Fig. 2.119. Secondary verification of the provision of the zolotnikovy valve of the operating oil valve: 1–oprezheny opening and closings of valves; 2–delay of opening and closing of valves; 3–zolotnikovy valve


Disconnect the storage battery and be convinced that the zolotnikovy valve returned to the provision of the maximum delay of opening or closing of valves of the engine. If it not so, replace the operating oil valve (fig. 2.119).

«previous page
2.2.12. Check of the operating oil valve (OCV) (L3)
following page»
2.2.14. The general repair operations on the power unit