Mazda 3 since 2003
1. Operation and car maintenance
2. Engine
3. Transmission
3.1. Coupling
3.2. Mechanical transmission
3.3. Automatic transmission
3.3.1. General information
3.3.2. Design and operation of the mechanism of transmission
3.3.3. System of electronic control (RSM)
3.3.4. Mechanism of switching of an automatic transmission
3.3.4.1. Principle of operation of the mechanism of switching of an automatic transmission
3.3.4.2. Check of blocking of switching
3.3.4.3. Check of blocking of the ignition key
3.3.4.4. Check of a cable of blocking
3.3.4.5. Check of the lever of the selector
3.3.4.6. Adjustment of a cable of a choice of transfer
3.3.4.7. Adjustment of the switch of a range of a transmission
3.3.4.8. Removal and installation of the lever of the selector
3.3.4.9. Installation of a cable of blocking
3.4. Driving mechanism
3.5. Tables
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
 








f084bf0f

3-3-4-8-snyatie-i-ustanovka-rychaga-selektora.html

3.3.4.8. Removal and installation of the lever of the selector

Fig. 3.88. Mechanism of switching of an automatic transmission: 1–facing of a steering column (with the mechanism of blocking of a key); 2–a clip (with the mechanism of blocking of a key); 3–a clip (with the mechanism of blocking of a key); 4–a blocking cable (with the mechanism of blocking of a key); 5–cable of a choice of transfer; 6–lever of the selector of a zaslonka


The mechanism of switching of an automatic transmission is shown on fig. 3.88.
Disconnect a negative wire of the storage battery.
Remove the storage battery and its tray.
Remove the air filter.
Remove the console.
Remove the dashboard.
Remove the module of management of the monitoring system of stability.

Fig. 3.89. Control unit removal by climatic installation: 1-cables of management of an air zaslonka; 2–block of climatic installation


Remove the control unit climatic installation (fig. 3.89).
Remove a back air line.
Remove facing of a steering column.
Disconnect clips and remove a cable of blocking and a cable of a choice of transfer.

NOTE
Installation carry out in an order specified in drawing 3.88. Separate procedures on removal and installation are described in this section below.


Fig. 3.90. Scheme of installation of a cable of a choice of transfer


To establish a cable of a choice of transfer it is necessary to establish at first it on an arm, as is shown in drawing 3.90.
Before replacement of a cable of a choice of transfer check that the lever of the selector is in situation P.

Fig. 3.91. Blocking of a clamp of a cable of a choice of transfer (from the selector lever)


Block a clamp of a cable of a choice of transfer (from the selector lever) in an order shown in drawing 3.91.

Fig. 3.92. Check of a shaft of manual switching


Check that the shaft of manual switching is in situation P (fig. 3.92).

ATTENTION
At installation of a cable of a choice of transfer hold it directly. Peregibaniye of a cable of a choice of transfer, as is shown in drawing 3.92, will lead to cable damage, it can become the reason of weakening of a cable when switching.

Fig. 3.93. The correct installation of the lever of the selector on the lever of a shaft of manual switching



NOTE
Establish the selector lever on the lever of a shaft of manual switching so that the spring of a tip of a cable of a choice of transfer was turned towards a forward part of the car (fig. 3.93).

Establish the selector lever on the lever of a shaft of manual switching so that the cable of a choice of transfer was not loaded.
Be convinced of that the end of the lever of a shaft of manual switching leaves a tip of a cable of a choice of transfer.
Establish a cable of a choice of transfer to an arm.

«previous page
3.3.4.7. Adjustment of the switch of a range of a transmission
following page»
3.3.4.9. Installation of a cable of blocking